• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace a 2013 kia sportage key fob programming Sportage Replacement Key

For a variety of Kia models keys, there is an integrated keyless entry system. The key can be compared to the remote control and can be exchanged with a new one from a Kia dealer or a locksmith.

Key fobs can stop working due to various reasons, such as a dead coin battery worn buttons or buttons, water damage, signal interference and a faulty receiver module. Here are some tips to assist you in getting your kia car key replacement sportage replacement key working again.

How to replace the remote key or smart key?

No matter if your kia replacement keys comes with an intelligent key, remote key, push to start key, or a standard non-transponder key made of metal, the battery in these keys will eventually require replacement. This is particularly the case if your car displays a message indicating that the smart or remote keys are not powered by batteries.

Luckily, it's an easy procedure. To replace the battery on the keyfob, remove your mechanical key from the slot at the back of the fob. Then, pry the cover open. A small screw will be located inside the key fob to keep the battery in the correct position. Remove the old battery by unwinding the screw with the help of a small screwdriver. Then, insert the new one and close the hole in the key fob.

Test the key fob by pressing the lock or unlock buttons. If the doors lock and unlock exactly as you expect, then you're good to go! You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers feel cold or you have to run errands around Brandon.

Note: Certain key fobs could need to be programmed (transponder chips or smart keys). This requires a particular programming machine that only the dealer or locksmith has access to. Other keys (non transponder metal keys) are not required for programming. If your key requires to be programmed, you will need to be aware of the number written on the tag that identifies the key and record it in a safe place.

How to replace a battery

If your Kia key fob isn't responding to pressing the lock or unlock button on the fob, it is a clear indication that the battery needs to be replaced. A low battery may also cause other problems like the check engine light coming on or the engine not cranking. It is relatively easy to replace the key fob battery with just some tools.

Make sure that you shut off your vehicle and shut the doors before you begin. Find the small metal or plastic piece near the bottom of the key fob. Jiggle it until the key is released. Then, you can insert this key into the door handle of the driver to open your car.

To replace the battery on the key fob remove the cover at the rear. Use a plastic pry tool to open the latch that holds the black negative cable. Remove the old battery, and then orient the replacement battery in a way that its "+" side is facing you, and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place, avoiding excessive force to avoid bending or damaging the contacts on the metal.

After you have installed the new battery then turn the key fob on and off in the ignition until the door locks up. Then, you can test your Kia key fob and see whether it's functioning properly again.

How to replace the smart key?

Depending on the model of your kia remote key fob Sportage, you may have the standard key fob, or a smart key. The smart key has an embedded mechanical key blade, while the standard key fob does not. Both key fobs have batteries that eventually require changing. Fortunately, it's quite simple and takes only two minutes.

Make sure you turn off your Kia and be on a level or well-lit surface prior to when you begin. Also, remember that there are tiny components inside the fob that could fall out if you are not vigilant.

The first step is to find the small release button on the lower backside of the fob. It's either an oval or circular slot. You can open the key fob by pressing the button.

Once you have the key fob open, you can simply remove the old battery, and replace it. The new battery should be a CR-2032, and can be purchased online or at a local auto parts store. When you're done, the key fob should be able to lock or unlock and start your vehicle even if it's not running.

How do I replace the mechanical key

The Kia key fob is a fantastic convenience that lets us lock and unlock our car at the push of a button. Like any other device it may have issues at times. There are solutions to address these issues and keep your key fobs working for a long time.

A dead or drained battery is among the most common problems. The battery could cause the device to stop working or work intermittently. If this is what you are experiencing, replace the battery with a new one.

If this doesn't solve the issue, use a flathead screwdriver standard to push the fob's casing made of plastic open. Be careful not damage any internal components, or scratch the plastic. After opening, carefully remove the old battery and replace it with a new one.

Close and open the door using the mechanical key. (Every kia Ignition key replacement fob comes with a spare mechanical key that fits into the slot). Test the key fob to verify that it's working correctly. If the key fob isn't working, contact an expert locksmith or dealer to help solve the problem. Make sure they cut you an emergency key that can work for all door and trunk cylinders to avoid future lockouts.