• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Go About Boarding Up a Door

The protection of vacant investment properties from the elements is feasible by board boarding up houses a door. Although it isn't able to be able to prevent all damage, it can avoid some of the problems that come with severe storms.

The idea of boarding up doors and windows can deter trespassers and vandals as well as squatters. Placing plywood boards over doors and windows could be time-consuming and costly.

Take a measurement of the door

First, you'll require a tape measure. It is also advisable to keep an extra chair or ladder for when you need to get a better look at the top of the frame. Wear gloves and goggles when you use these tools.

Begin by measuring the length of the door. This can be done by running a tape measure horizontally along the door. Make sure to remove any extra parts of the door, for instance the sweep, when measuring. Then, determine the height measurement by measuring from the floor to the current sill plate or the lintel. It is essential to measure multiple locations especially for older doors, as they are not always a perfect rectangle. If the measurements are different, use the largest figure.

You'll have to determine the dimensions of the frame after you've taken measurements of the length and width. It should be at minimum 2 inches wider and 1'' taller than the door. 2'' higher. This will allow plenty of room to move the frame and door into place.

It's a great idea to remove the casing or trim around the jambs of the door to be able to see the studs. This will enable you to take measurements of the exact gap between the studs of the frame and the edge.

After removing the trim, measure the width of the door frame using a tape measure. The frame should be measured at three different points and then use the smallest measurement. Also, you should measure the frame's height from top to bottom on both sides. Use the shortest measurement for your door's width.

If you're having issues with the measurements, you should seek out a professional who will come to your home and take the measuring. They'll inform you of the dimensions and what kind of door you require and how to prepare your frame to accommodate a replacement door.

Cut the Plywood

A door frame is typically made emergency boarding up 24/7 of a series thin boards or studs which create a hollow space surrounding the door. Two hinges are attached to the studs and keep the door in its place. If you are looking to refinish a door, you will have to remove it from its hinges over night. To keep insects out of your home and to secure the door's opening, a simple method to board doors is to place plywood in the opening. This is easy to do without the need to screw or nail the plywood to the frame of the door.

Plywood is a breeze to work with, affordable and looks beautiful once completed. This makes it the perfect material for an interim solution to an issue that requires the removal of the door that is in use and renovating or installing a brand new one. It can also be used to secure the opening of a room being renovated, like a basement or construction site.

To install a plywood wall begin by taking measurements of the width and height of the door opening. Note the measurements using an utility blade and a straight edge of metal like a drywall or a metal square. Then, draw the chalkline along each line to indicate where to cut. Utilize a circular saw to cut the plywood to size.

It is important to protect both your ears and eyes while cutting plywood. Wear earplugs or protective goggles whenever possible. In addition, it's crucial to use a knife with a lot of teeth that will cut quickly and without tear-out. To minimize the chance of cutting pieces of wood from the edges of your cut using a small piece of wood as template to guide the blade and hold it just a hair's width away from the marked line while cutting.

Attaching a pair or short braces at each end is a great way to secure the plywood in place without putting screws into the studs. Set one brace on the side of the door, and the one on the outside. Then, insert two 1-1/2-inch deck screws into each of the holes and tighten them using an open-end wrench.

Fasten the Plywood

When you have a piece of plywood cut to the appropriate size and with the holes for rails and boarding Up companies stiles already drilled, it is time to fasten the panel to the frame. This is a simple task that doesn't require a lot of advanced carpentry skills if you use the right tools and follow the correct steps.

Set boarding up windows a table near the doorway with two sawhorses on each end, as well as framing 2x4s. Lay the entire sheet of plywood flat on top the sawhorses, using the marks from the measurement process as a reference to cut. Utilize a utility blade and a straight edge of metal to cut the lines. This will serve as an outline for the saw blade, and will help keep the wood from splintering when cutting the plywood.

Put on eye protection and cut along the lines of scoring using a circular saw or table saw with a fine-tooth blade. Sand the edges of the panel using 120-grit paper to smooth it out and eliminate any burrs. After sanding the plywood then apply a wood sealer and let it dry in accordance with the manufacturer's guidelines.

Install the hinges on the door frame. If you're using T hinges, make holes through the exterior of the door for the strap portions of the hinges. Then, screw the hinge's outside edge to the frame using a screwdriver. Repeat the process on the inside of the door for the remaining hinges, being careful not to overtighten any of them, or the door will shift.

If you have a single hinged T on your outside door you can make it easier for the latch to close by fishing an electrical wire through the loops of the outside hinges. Fold a small piece of make a half-way tie, and then thread it through the two holes on the outside of the door. Then, you can twist the wires together and fix the door.

Install the Plywood

Using the measurements you took and place the plywood into the door opening. Move the frame's header (top) and the sill. Utilize a level and ensure that there's no slop between the header and sill. If it's not quite right, put another shim in the area is required and repeat the process until you have the sill and the header to be level.

Once the plywood has been put in place, fix it with the stainless-steel hinge bolts and wingnuts. It is a good idea to utilize a screw gun that has a hex-head attachment to prevent stripping the head of the screws.

If your house has studs running the length of your doorway, you could drill hanger bolts into every framing piece. This is much easier than using a drywall cutter to create the hole.

After you have installed the plywood, take measurements of the width and height of the door opening. If needed, trim the bottom plywood to match the height your door frame. Cut two pieces of framing wood 1-by-6 to form braces for the upper and lower ends. Cut along the lines marked on your plywood using circular blades with fine-toothed teeth. Wear eye protection. Remove any splinters from the cuts using a sanding block.

After you have the braces in place Attach each brace to the plywood with pairs of finishing nails that measure 2 inches. When you're finished, counter sink the heads of all the nails. Cover the braces using a high-quality wood sealing product, like the wipe-on polyurethane made by Minwax.

If the door is too large it is possible to add decorative molding to fill the gap between your door and jamb or you can reduce the size of your opening. However, in many cases, it's cheaper and simpler to just choose a new door. This will also take away any issues that you might have faced with the original door, if it was damaged and could no suitable for the opening.