• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Go About boarding up door Up a Door

The act of emergency boarding up near me boarding up houses a door is one way to protect vacant investment properties from the elements. While it won't be able to prevent all damage, it can reduce certain problems that can arise from severe storms.

boarding up and burglary repairs up windows and doors (Read the Full Content) can deter trespassers, vandals, and squatters. However, it can be expensive and time-consuming to put plywood boards over the openings on a house.

Take a measurement of the door

The first thing you'll require is tape measure. You may also want to have an extra chair or ladder for when you need to get a better look at the top of the frame. Wear gloves and goggles when you use these tools.

Once you have the measuring tool, start by taking the door's width measurement. This can be done by running the tape horizontally across the door. Make sure to remove any additional door parts such as the door sweep, from this measurement. Next, measure the height by measuring from the floor to the existing sill plate or the lintel. It is essential to measure in more than one location, especially with older doors, because they are not always an exact rectangle. If the measurements are different take the largest number.

You'll have to determine the size of the frame after you've measured the width and height. It should be at a minimum 2'' wider and 1 inch taller than the door. 2'' higher. This will give you plenty of space to put the door and frame to fit.

When you're ready to take the door frame's width and height measurements, it's recommended to remove any trim or casing from the door jambs, so you can see the studs behind them. This will let you determine the exact distance between the frame's studs and the edge.

Once you've removed the trim, you can measure the size of the door frame by running the tape over the entire frame in three places and using the smallest measurement to determine the width of your door. Also, you should take measurements of the frame's height from top to bottom, on both sides. Make use of the shortest measurement to determine the width of your door.

If you're having difficulty with the measurements, seek out a professional who will come to your house and conduct the measurement. They'll inform you of the size and type of door you'll need and how to prepare your frame for a replacement door.

Cut the Plywood

A door frame is usually comprised of a set of thin boards or studs which create a hollow space surrounding the door. A typical door is held in place by two hinges connected to the studs. This means that, if you wish to refinish the door, it's necessary to remove the hinges from the door over the course of a few days. Placing plywood into the door opening is a simple method to board the door and keep insects from getting into your home. It is easy to do this without nailing or screw the plywood onto the frame of the door.

Plywood is affordable, simple to work with and looks fantastic when finished. It is the perfect material to make a temporary solution to a problem in which you have to take down an existing door to refinish or install an entirely new one. It can also be used to secure the opening of a room being renovated, like the construction site or basement.

Begin by measuring the width of your door opening and its height. Note the measurements on the plywood with the help of a utility knife, an drywall square or any other straight edge of metal. Then, you can snap the chalkline along each line to mark the area to cut. Utilize a circular blade to cut the plywood to the desired size.

When cutting the plywood it is important to protect your ears and eyes. Wear protective goggles or earplugs if possible. Additionally, it is important to use a blade with a lot of teeth that cut quickly and with minimal tear-out. Use a small piece of wood to guide the blade. Keep it a hair's breadth away from the mark when cutting.

Attaching a pair or short braces to each end is a good way to hold the plywood in place, without screwing it into the studs. Place one brace on the inside and the other on the outside of the door. Then, position two 1-1/2-inch deck screws in each of the holes and tighten them using an open-end wrench.

Fasten the Plywood

When you have a piece of plywood cut to the right size and with holes for the door frame's rails and stiles already drilled then it's time to fasten the panel to the frame. This is a straightforward project that does not require a lot of carpentry expertise, so long as you follow the correct procedures and use the proper tools.

Set up a table near the entrance with two sawhorses on each end, and framing lumber 2x4s. Lay the entire sheet of plywood flat on top the sawhorses, using the marks from the measurement process to guide you to cut. Cut the lines using the help of a utility knife, a drywall square or other metal straight edge. This will serve as a guide for the saw blade and will prevent splintering of the plywood when cutting it.

Wear eye protection and cut along the scored lines using a circular or table saw equipped with a fine-tooth blade. Then, sand the edges of the plywood panel with 120-grit sandpaper. This will smooth out the panels and remove any burrs from the saw cuts. After the sanding, apply a coat of wood sealer on the plywood panels and allow to dry according to the instructions of the manufacturer.

Install the hinges on the door frame. If you're using a T hinge, drill holes in the outside of the door to accommodate the straps of the hinges. Then, screw the hinge on the outside to the frame with the screwdriver. Repeat the process for every hinge on the inside of your door. Be cautious not to overtighten them, or the door may shift.

If you have only a single hinged outside door you can make it easier to close by placing an electrical wire through the loops of the outside hinges. Fold a piece of connect wires in half and then thread it through the two holes on the outside of the door. Then, twist the wires together and fix the door.

Install the Plywood

Using the measurements you took, place the plywood in the door opening. Change the frame's header (top) and the sill. Utilize a level to make sure there's no slop in either the header or sill. If it isn't perfect, place another shim where necessary and continue the process until the header and sill are plumb.

After the plywood is in place, secure it using the stainless-steel hinge bolts and wingnuts. Make use of a screwgun that has an attachment for hex heads to avoid stripping off the screws' heads.

If your house has studs running the length of your doorway, you can drill hanger bolts into every framing piece. This is a much easier task than cutting the hole with the aid of a saw for drywall.

After putting the plywood in place, take measurements of the width and height of the door opening. If needed, trim the bottom plywood to be a little higher than the height of your door frame. Cut two pieces of framing wood 1-by-6 to serve as braces for the upper and lower ends. Cut along the lines drawn on your plywood with circular blades with teeth that are finely tipped. Wear eye protection. Get rid of any splinters that may have formed in the cuts by using an sanding block.

After you've placed the braces After you have placed the braces, use two pairs 2-inch finishing nail to attach each brace to the plywood. After you're done, counter sink the heads of all nails. Make sure to seal the braces and the plywood with a high-quality wood sealer, such as this wipe on polyurethane from Minwax.

If the door is too large for your doorway, you can add some decorative molding to fill in the gap between the jamb and the door or you can alter the size of the opening. However, in most cases, it's cheaper and simpler to just choose a new door. This can also alleviate any problems you might have had with the door you originally purchased if it was damaged and could no fit for the opening.