• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to repair car keys (read the article)

Car keys may appear tiny and insignificant, however they are essential for the proper operation of your vehicle. Replacing a traditional or a transponder one could cost as much as $200.

There are many ways to repair your car keys yourself at a fraction of the price. This article will cover some of the most frequent car key problems and their DIY solutions.

Dead Key Fob Batteries

The remote key fobs for keys that come with cars make it easier than ever before to open the trunk, doors and the tailgate. However, the battery inside the device can fail. There are, however, a few tricks you can employ to resolve this issue in an emergency.

First, determine if the car is still in ignition mode. If it is the battery of the key fob may be low, but not dead. To test this, push the button on the key fob straight towards the ignition button. If it works, then the battery is probably in good condition and only has to be replaced.

To replace the battery inside the fob, pry open the case using the screwdriver. Be cautious not to apply too much pressure because this could cause the fob to split into two pieces. If the fob isn't coming open with ease, try placing your pry tool in multiple places around the outside of the case.

Once the fob is opened then remove the mechanical key and open the electronic section of the car. Insert the new battery and snap back the shell. If the key fob doesn't work after this procedure, there could be a bigger issue with your car's remote start system that requires a professional diagnostic. If this is the case, a trusted mechanic should be able assist you. If you need help with your vehicle key repairs and you need help, you can call roadside assistance.

Broken Key Ring

There are a few options you can do if your key fob doesn't function because the ring is broken. First, you should check to see if your broken piece is still in the ignition. If it is, remove it without damaging the lock on the ignition or door lock. If you have trouble getting it out, contact an expert locksmith. They have specialized tools that allow you to safely remove the damaged key from the ignition.

Another common cause of broken car keys is the corrosion of the circuit board or plastic frame. It is possible to clean the board with rubbing alcohol and a cotton swab. This will remove corrosion and ensure the contact pads aren't damaged.

repair car key a damaged ring by using a thick nail or wire to close the hole. You can also use superglue to repair a broken ring. After cleaning the ring using a damp cloth, apply a small amount superglue to each end of the nail or wire. Let the pieces dry and then press them into place. These DIY solutions may appear appealing, but they're really just a stopgap measure. For long-term repairs, you'll want to hire an expert locksmith. They have the expertise and tools to fix damaged keys quickly and efficiently. They can replace the battery and reprogram the key fob, if needed.

Broken Key Blade

Some key blades can break due to a lot of wear and tear. If this happens, it's time to buy a new key. This problem isn't nearly as serious as you might think at first glance. The main problem is that the metal blade has snapped away from the case.

One solution is spraying the key hole with lubricant. Then, you can use pliers or tweezers to grab the broken end of the key and pull it. You may also employ a magnet in the event that the key is magnetic. Use a magnet to help you remove the key, but take care to not damage the tumbler of the lock.

Contact a locksmith immediately in the event that you are unable to take out the damaged part of the key. They have special tools to safely extract keys without causing any further damage.

You can also try super glue to fix a broken key. Apply a small amount to the edges and press them in. After that, wait until the glue dries before you insert your key into the lock. This method isn't very reliable, and you may have to repeat it a few times before it works. In addition the super glue may not be strong enough to hold the key together. This is more of a temporary measure rather than an option that can last.

Broken Plastic Loop

If the plastic loop is damaged it could render the key ineffective. Fortunately, this is an simple fix. You can make use of wire or a nail for finishing as a replacement. Drill two holes in the damaged loop of plastic at each end of the nail or wire. Cut the nail or wire to key width and place a drop of superglue on each hole. Press the nail or wire into the holes and allow them to dry.

A locksmith who sells replacement shells is an alternative option. They can take the programmable part of your key repair car, move it to the new shell, and cut a new blade for much less than a complete replacement cost.

It's not the most ideal solution, but it can bring you back on the road in case your key split in half. However, it could be difficult to fix the key blade if it is in the ignition. If you are not careful, you can use a hair clip or needle to remove the broken part from the ignition. The best option is to contact a locksmith who has special tools for safely removing damaged keys from the ignition. They can also design a new key with the correct cuts for your ignition, so it will work properly when it is inserted into the lock.

Broken Master Key

If a key breaks inside the lock, you'll have to attempt to retrieve it before it is completely destroyed. You can make use of tweezers, lubricants, and needle nose pliers to grasp the fragments of a damaged key.

Spray the inside of the lock with WD-40 or a graphite powder. You can also employ the hacksaw blade technique, which involves moving the blade along the sides of the broken key, and grasping onto a few of its 'teeth. If you're successful then you should be able to remove the broken key.

Another helpful tool is a spiral key extractor, which you can find in a variety of hardware stores. This tool has a thin rod with spiral threads that can be inserted into the keyway and then bent to the broken portion of the key. Once it has caught onto the serrations you can twist the bar into a circle and then pull it against the broken part of the key.

It's worth attempting to remove the master key that is broken before calling an expert locksmith. If you're not able to take the broken piece off it's time to call a locksmith. A locksmith can make you a new key that will be programmed with your car transponder.