• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Repair French Doors (Zenwriting.Net)

French doors can be a stylish method of connecting indoor and outdoor spaces. However, they could face problems over time that require prompt attention for both safety and functionality.

Common problems include problems with alignment, sagging, and warping of the door's frame and sash. Many of these issues can be solved with some time and effort.

Locks that are misaligned

Sometimes doors get stuck or misaligned due humidity, swelling of the wood or the house shifting. This could cause the lock bolt or strike plate sway and require more force to open and close the door. This can put extra stress on the lock, which could eventually result in mangled inner-lock components or even broken locks altogether. This is fortunately an issue that is quite common and can be resolved with simple DIY solutions.

In some instances it is possible that a small amount of lubricant may be all you need to make the door easier to open and close. You can use graphite lubricant, but make sure it's safe for the door. Be sure to clean the area with a damp cloth to eliminate any dirt around the door prior to you apply the lubricant.

Another method to fix a door hanging off the wall is by loosing the hinges and then moving them until they're in line with the frame of the door. Be careful not to over-tighten the screws because this could damage the hinges or door.

If your exterior French door isn't closing properly, it could be a sign that there is a blockage in the lock mechanism. This is usually caused by factory screws that are short that become loose over time. Replace the screws with longer ones to remove more wood from the door frames.

You can also try adjusting the lock, but this will be more complicated and difficult. Begin by loosening the knob of the lock or handle with a flathead screwdriver. Then, you can remove the lock assembly from its cubbyhole by unscrewing and pulling it out. Look for obstructions, and then reassemble the lock and tighten all screw connections.

If the latch isn't touching the strike plate hole it may be necessary to alter or increase the size of the strike plate hole. If the strike plate is either higher or higher than the latch hole it can stop the lock from closing and will require a professional locksmith. If the hole is too small, you can increase it with a metal file or drill.

Sagging

If your doors sag or have gaps, it will decrease the energy efficiency of your home. These gaps can also cause drafts and obstruct your view. Fortunately, there are a few simple solutions that can help resolve these issues.

In the beginning start by tightening your hinges to ensure they are properly aligned. This should take about 10 minutes and no tools are required. If this does nothing to fix the issue, you will need to replace the hinges. They are likely to be nearing the end of their lifecycle.

Over time the replacement french door doors can loosen because of the weight. To prevent this from happening ensure that the hinges are secured your door and make sure they are secure. It is also recommended to regularly lubricate your hinges with a spray of lubricant to extend their lifespan.

Old or damaged hinges can cause doors to sag and sag, so replacing hinges with new ones can help. A new doorknob or freshly painted doors can also impact the alignment of your French door.

Other causes of sagging can be foundation settlement, wear and tear on the hinges or improper modifications to your doors. A door that is sagging can be corrected by adjusting the hinges or tightening the hinge screws or even replacing french doors with windows the hinges completely.

Also, it is important to inspect the weather stripping on your doors and to make sure they are functioning correctly. If they're not, then removing them and replacing them should solve the issue.

Also, you should examine your door frames for signs of warping or rot. These issues can create a draft and will not only reduce the efficiency of your doors, but could also cause water leakage and other damages around your home.

Popular Mechanics advises that if your doors are sagging, and you've tried the first two options, you may have to sand the door jambs using a handplane. To do this, take your doors from the hinges. Set them flat on something sturdy like a sawhorse. Note the areas that require smoothing, and then use a plane to smooth these areas.

Leaks

French doors with large glass areas are prone to leaks, especially when you live in a region that receives heavy rain. Untreated, these leaks may cause the frame of the door to decay and damage the structure around it to deteriorate. Fortunately, fixing these leaks is a relatively simple task that will take only just a few hours to finish.

Leaks are caused by many causes, including

A broken seal

Replace the rubber seals that are on either side of your threshold with new seals. This will ensure a tight fit, and will also stop rainwater from getting inside your home.

The sill is leaking with water.

The problem could be caused by through a variety of causes, including the lack of a sillpan, or using a sill made of metal that is not watertight. If you see water accumulating around your French doors, it's important to get in touch with the builder and ask for the installation of a sill pan or to replace french doors with bifold the sill made of steel by a wooden one that will be able to resist moisture.

Obstructions

A leaky seal could result in fog accumulating between the double panes of glass on French doors, which obstructs the view and lowers energy efficiency levels. This can be corrected by replacing the seal with one that is able to stop moisture and air from entering.

Loose Handles

A handle that is loose could be dangerous since it could fall while you are opening or closing your french door glass replacement inserts door. This issue can be solved by tightening the screws, or replacing the handle if it's damaged or worn.

Similarly, a track stop that's not properly set can stop doors from sliding properly, resulting in jams and scratches on the frames. Applying silicone caulk to the tracks or track stops can help with this issue. It's also an excellent idea to check for cracks regularly and wear on exterior surfaces of doors and frames to ensure that they are in good condition.

Warping

A French door has a stunning view and lets in plenty of light. However, when you're not cautious, your doors can start warping due to exposure to heat or humidity. It's worth calling in a handyman with experience in fixing your French door. They will be able to guide you on the best way to repair your doors and ensure that they are safe to open and close.

If your doors are badly bent, you may have to replace bay window with french doors them completely. However, if they're just slightly warped, it may be possible to bring them straight by soaking heavy towels and placing them across the area of concern. The towels should remain in place for several days or more until the doors are completely flattened.

This method is often used on uPVC doors, but can also be applied to wooden doors if the wood is well-seasoned. The process is difficult and time-consuming, particularly when your doors are distorted.

Doors can crack in the event that they were stored incorrectly. They should be kept clear from building works that generate a lot of humidity like decorating or plastering work. They should also be stored flat on a smooth surface and not stacked especially in their unfinished state.

Another cause of warping is an unfastened strike plate. To correct this, you need to take the doors off and set them up on two sawhorses. The excess wood can be removed from the bottom and top edges of each door with a hand plane. It is recommended to work in smaller increments to avoid taking too much wood from the doors. This could result in them becoming too thin and brittle.

Once the doors are put back up, you can screw the strike plate back into place. If the lock doesn't work, the barrel catch may be getting caught on the side of the frame. This is fixable by spraying silicone on the latch. If that doesn't help the latch, it may need to be replaced.